default static route example For example if you use the following commands to create two static routes for network 30 0 0 8 the route will place the first route to the routing table ip route 30 0 0 0 255 0 0 0 20 0 0 2 10 ip route 30 0 0 0 255 0 0 0 40 0 0 2 20
Learn how to configure a static default route through a practical example in the Packet Tracer By default if the destination network address of an incoming packet is unknown to the router the router forwards that packet from the default route Example The Address of Yahoo is unknown It is the last preferred routing Also can be used at end locations Default routes help in reducing the size of your routing table CLI command R 1 config ip route any destination any subnet mask next hop IP address R 1 config ip route 0 0 0 0 0 0 0 0 10 0 0 2
default static route example
default static route example
https://www.learncisco.net/wp-content/themes/learncisco/assets/images/icnd1/92-static-default-route.jpg
Default Static Route
https://study-ccna.com/wp-content/uploads/2019/11/default_static_route_example_network.png
07 The Default Static Route YouTube
https://i.ytimg.com/vi/fRyDav7Cu-M/maxresdefault.jpg
A default static route is a route that matches all packets A default route identifies the gateway IP address to which the router sends all IP packets that it does not have a learned or static route for A default static route is simply a static route with 0 0 0 0 0 as the destination IPv4 address Configuring a default static route creates a Let s use an example to illustrate the configuration process for static and or default routes RouterA is directly connected to networks 195 14 25 40 30 195 14 125 48 30 and 192 168 10 0 24 In order for RouterA to be able to route packets to all other networks the following static routes need to be configured on the router
Default Routing This is the method where all routers are configured to send all packets towards a single router This is a very useful method for small networks or for networks with a single entry and exit point It is usually used in addition to Static and or Dynamic routing As a system administrator you can configure static routes using the ip route command To display the IP routing table use the ip route command For example ip route default via 192 168 122 1 dev ens9 proto static metric 1024 192 168 122 0 24 dev ens9 proto kernel scope link src 192 168 122 107
More picture related to default static route example
Configure Floating Static Routes Ccna Hot Sex Picture
https://www.ciscopress.com/content/images/chap2_9781587133237/elementLinks/02fig67_alt.jpg
Default Route And Static Routes Configuration Ccna Study Guides
https://i.pinimg.com/originals/ac/74/c8/ac74c8be528efd54440dc5aa7c22e67b.jpg
How To Configure Static Route IPv4 And IPv6 NetworkUstad
https://i0.wp.com/networkustad.com/wp-content/uploads/2019/08/show-ip-route-router2.png
Ciscoasa config ipv6 route inside 7fff 0 32 3FFE 1100 0 CC00 1 110 Adds an IPv6 static route to the IPv6 routing table The example routes packets for network 7fff 0 32 to a networking device on the inside interface at 3FFE 1100 0 CC00 1 and with an administrative distance of 110 Step 1 Static routes have a default administrative distance of 1 A router prefers a static route to a dynamic route because the router considers a route with a low number to be the shortest If you want a dynamic route to override a static route you can specify an administrative distance for the static route For example if you have two dynamic
About Static and Default Routes To route traffic to a non connected host or network you must define a route to the host or network either using static or dynamic routing Generally you must configure at least one static route a default route for all traffic that is not routed by other means to a default network gateway typically the next The following image shows both commands with sample output Static default route v s Dynamic default route A default route configured by the ip route command is called the default static route Some routing protocols such as RIP and EIGRP allow us to advertise the default static route
Configuring IPv4 Static Routes YouTube
https://i.ytimg.com/vi/m8CDaVBZjtg/maxresdefault.jpg
Configuring A Static Default Route
https://www.freeccnaworkbook.com/images/lab-6-3-logical-topology.JPG
default static route example - By default static routes have an administrative distance of 1 making them preferable to routes learned from dynamic routing protocols For example the administrative distances of some common dynamic routing protocols are EIGRP 90 IGRP 100 OSPF 110 IS IS 115 RIP 120